A channel die compression simulation on Mg AM30

From EVOCD
(Difference between revisions)
Jump to: navigation, search
 
Line 34: Line 34:
 
}}
 
}}
  
[[Category: Research Paper]]
+
[[Category:Channel Die Decomposition]]
[[Category: mesoscale]]
+
 
[[Category: magnesium]]
 
[[Category: magnesium]]
 +
[[Category: mesoscale]]
 +
[[Category: Research Paper]]
 
[[Category: VPSC]]
 
[[Category: VPSC]]

Latest revision as of 09:43, 16 April 2015

AbstractMethodologyMaterial ModelInput DataResultsAcknowledgmentsReferences

Abstract

Deformation of polycrystalline aggregates of HCP crystals was investigated by employing crystal plasticity and finite element simulations. Results were validated using channel die compression tests. The three dimensional polycrystal, represented by Voronoi techniques, was assigned an initial distribution of crystallographic orientations determined from X-Ray Diffraction. The mechanical properties from the channel die compression tests were used to correlate the material parameters of the crystal plasticity model. Simulations predicted grain-to-grain interactions and the resulting texture evolution under channel die compression. The inhomogeneous deformation among grains was mapped by a stress and a strain distribution and grain orientation spread. The simulation results were compared with experimental observations of an HCP polycrystal subjected to channel die compression.

Author(s): Q. Ma, E.B. Marin, A. Antonyraj, Y. Hammi, H. El Kadiri, P.T. Wang and M.F. Horstemeyer


Figure 1. (a)Initial texture; (b) undeformation 3D Voronoi structure; (c)channel die compressed 3D Voronoi grains; (d) materials point simulated and measured stress-strain curves and (e) crystal plasticity and 3D structure predicted and measurd stress-strain curves. (click on the image to enlarge).

Methodology

Magnesium has a hexagonal close-packed (HCP) structure whose deformation modes are different from those of aluminum. Typical deformation modes in magnesium are basal <a>-{0002}<11-20> slip, prismatic <a>-{10-10}<11-20> slip, second pyramidal <c+a>-{11-22}<11-23> slip and extension twinning {10-12}<10-11>. In this study, a commercial extruded AM30 alloy (mass %, 2.54% Al, 0.40% Mn, Mg in balance) was selected as the HCP experimental material to conduct channel die compression at high temperature 200C and at strain rate of 0.001/S to strain 30%. At these loading conditions, twinning would not be profuse and, hence, only slip will be the predominant deformation mode. The hardening parameters of the three slips modes were obtained using material point simulations to fit the experimental stress-strain curve recorded from the channel die compression test as shown in Figure 1d.

The texture of AM30 was measured by X-ray diffraction method (XRD). The recalculated pole figures were calculated based on the orientation distribution functions (ODFs) which was obtained using the measured six incomplete pole figures {10-10}, {0002}, {10-11},{10-12}, {11-20} and {10-13}. The initial and the channel die compressed texture of AM30 plotted by the texture software MTEX [1].

The commercial finite element software ABAQUS 6.9 and a user subroutine UMAT incorporating the crystal plasticity constitutive theory and the magnesium AM30 materials parameters were used to simulate texture evolution and mechanical response. The initial texture used in this CPFEM simulation was measured in the undeformed sample and was represented by 343 discrete orientations as shown in Figure 1a. The 3D polycrystal is represented by the 3D Voronoi grains created by the code Neper [2]. The undeformed polycrystal and the channel die compressed 3D polycrystal up to a strain of 30% are presented in Figures 1b and 1c.The simulated and measured channel die compression stress-strain curves are presented in Figure 1e.

Material Model

VPSC: ViscoPlastic Self-Consistent

Input Data

See VPSC Input Deck for a channel die compression simulation on Mg AM30

Results

Plane strain compression simulations of a three dimensional microstructure of HCP magnesium AM30 were performed using an elastic-plastic crystal plasticity model and the finite element method. The mechanical response, global texture evolution and the intergranular heterogeneous plasticity of discrete grain were captured by the 3D Voronoi microstructure channel die compression simulation. Simulation results showed that the effect of grain interaction could play an important role on global texture evolution, the orientation spread and the local heterogeneity deformation of one grain.

Acknowledgments

The authors are grateful to the financial support from the Department of Energy, Contract No. DE-FC-26-06NT42755, and the Center for Advanced Vehicular Systems (CAVS) at Mississippi State University.

References

  • Antonyraj, A., Marin, E., Ma, Q., Wang, P., Horstemeyer, M., & King, R. (Oct 2010). Re-Crystallization Studies of a Channel-Die Compressed AM30 Magnesium Alloy. TMS 2011, California.
  • Ma, Q., Marin, E., Antonyraj, A., Hammi, Y., Wang, P., & Horstemeyer, M. (Oct 2010). On Predicting the Channel Die Compression Behavior of HCP Magnesium AM30 Using Crystal Plasticity FEM. Magnesium Technology 2011, 583-587. Proceddings of 2011 TMS Annual Meeting and Exhibition, San Diego, California, USA.
Personal tools
Namespaces

Variants
Actions
home
Materials
Material Models
Design
Resources
Projects
Education
Toolbox