# AZ61A

(→Fitting Procedure) |
(→Fitting Procedure) |
||

(8 intermediate revisions by one user not shown) | |||

Line 3: | Line 3: | ||

= Source Data = | = Source Data = | ||

− | The source data was based on the digitization of AZ61A stress-strain curves. A compression and a tension stress-strain curves, respectively, were digitized. | + | The source data was based on the digitization of AZ61A stress-strain curves. A compression and a tension stress-strain curves, respectively, were digitized. The environment temperature and strain rate were not specified, on the diagrams, so they were assumed to be 293K and 0.001 1/s respectively. |

[[image:AZ61A Mg Compression.png|thumb|320px| | [[image:AZ61A Mg Compression.png|thumb|320px| | ||

Line 27: | Line 27: | ||

* [[File:AZ61A-Mg-Compresion.txt]] | * [[File:AZ61A-Mg-Compresion.txt]] | ||

* [[File:AZ61A-Mg-Tension.txt]] | * [[File:AZ61A-Mg-Tension.txt]] | ||

+ | |||

+ | {| class="wikitable" style="width:480" | ||

+ | |+ Material and environmental parameters for Mg AZ61 alloy | ||

+ | |- | ||

+ | ! Constant | ||

+ | ! Value | ||

+ | |-- | ||

+ | | Temperature | ||

+ | | 293K | ||

+ | |-- | ||

+ | | Strain rate | ||

+ | | 0.001 1/s | ||

+ | |-- | ||

+ | | Young's modulus | ||

+ | | 44.8 GPa | ||

+ | |-- | ||

+ | | Poisson ratio | ||

+ | | 0.35 | ||

+ | |} | ||

+ | |||

<br clear=all/> | <br clear=all/> | ||

Line 34: | Line 54: | ||

We followed the general outline of the fitting procedure detailed on the [[DMGfit_55p_v1p1]] page with some modifications to accommodate for the types of available data. For example, temperature dependence constants were not fitted because we did not have temperature dependent data. | We followed the general outline of the fitting procedure detailed on the [[DMGfit_55p_v1p1]] page with some modifications to accommodate for the types of available data. For example, temperature dependence constants were not fitted because we did not have temperature dependent data. | ||

− | First we preformed a rough manual fit, by adjusting several of the Cn constants as detailed below, followed by an automatic optimization for the same set of constants. The initial manual fit helped the goal seeking algorithm move in the right direction toward convergence and converge faster. | + | First we preformed a rough manual fit, by adjusting several of the Cn constants as detailed below, followed by an automatic optimization for the same set of constants. The initial manual fit helped the goal seeking algorithm move in the right direction toward convergence, and also helped the algorithm converge faster. |

− | The following parameters were fitted manually the order listed below: | + | The following parameters were fitted manually in the order listed below: |

− | + | # Fit C3, which is the yield stress. | |

− | + | # Fit C9, C7 | |

− | + | # Fit C15, C13 | |

− | + | # Fit Cb | |

− | + | # Readjust C9, C7, C15 and C13 after fitting Cb. | |

− | Finally, we performed an optimization procedure. To do this we unchecked the parameters mentioned above, while leaving the rest of the parameters checked and hit the 'optimize' button. | + | Finally, we performed an optimization procedure. To do this we unchecked the parameters mentioned above, while leaving the rest of the parameters checked and hit the 'optimize' button. The results are detailed in the section below. |

Line 52: | Line 72: | ||

[[image:AZ61A-Fit.png|thumb|320px| | [[image:AZ61A-Fit.png|thumb|320px| | ||

− | + | Screenshot of the DMGfit UI after performing the fitting operations listed in [[AZ61A#Fitting_Procedure]] | |

]] | ]] | ||

+ | |||

+ | |||

+ | {| class="wikitable" style="width:480" | ||

+ | |+ Estimated constants and their values | ||

+ | |- | ||

+ | ! Constant | ||

+ | ! Value | ||

+ | ! Meaning | ||

+ | |- | ||

+ | | C3 | ||

+ | | 100 MPa | ||

+ | | Rate independent yield stress | ||

+ | |- | ||

+ | | C5 | ||

+ | | 1e-05 1/sec | ||

+ | | Transition strain rate from rate independent to dependent yield | ||

+ | |- | ||

+ | | C7 1/MPa | ||

+ | | 9.16489 | ||

+ | | Kinematic recovery constant | ||

+ | |- | ||

+ | | C9 | ||

+ | | 19485.5 MPa | ||

+ | | Kinematic anisotropic hardening modulus | ||

+ | |- | ||

+ | | C13 | ||

+ | | 282.43 1/(MPa sec) | ||

+ | | Isotropic dynamic recovery | ||

+ | |- | ||

+ | | C15 | ||

+ | | 109944 MPa | ||

+ | | Isotropic hardening modulus | ||

+ | |- | ||

+ | | Cb | ||

+ | | 1.49397 | ||

+ | | Tension/compression asymmetry constant | ||

+ | |} | ||

+ | |||

<br clear=all/> | <br clear=all/> |

## Latest revision as of 16:51, 25 April 2016

The damage model parameters for Magnesium AZ61A alloy were fitted using DMGfit_55p_v1p1. The original sources, the fitting procedure and results are detailed below.

## Contents |

# [edit] Source Data

The source data was based on the digitization of AZ61A stress-strain curves. A compression and a tension stress-strain curves, respectively, were digitized. The environment temperature and strain rate were not specified, on the diagrams, so they were assumed to be 293K and 0.001 1/s respectively.

Digitized data files:

Constant | Value |
---|---|

Temperature | 293K |

Strain rate | 0.001 1/s |

Young's modulus | 44.8 GPa |

Poisson ratio | 0.35 |

# [edit] Fitting Procedure

We followed the general outline of the fitting procedure detailed on the DMGfit_55p_v1p1 page with some modifications to accommodate for the types of available data. For example, temperature dependence constants were not fitted because we did not have temperature dependent data.

First we preformed a rough manual fit, by adjusting several of the Cn constants as detailed below, followed by an automatic optimization for the same set of constants. The initial manual fit helped the goal seeking algorithm move in the right direction toward convergence, and also helped the algorithm converge faster.

The following parameters were fitted manually in the order listed below:

- Fit C3, which is the yield stress.
- Fit C9, C7
- Fit C15, C13
- Fit Cb
- Readjust C9, C7, C15 and C13 after fitting Cb.

Finally, we performed an optimization procedure. To do this we unchecked the parameters mentioned above, while leaving the rest of the parameters checked and hit the 'optimize' button. The results are detailed in the section below.

# [edit] Results

Constant | Value | Meaning |
---|---|---|

C3 | 100 MPa | Rate independent yield stress |

C5 | 1e-05 1/sec | Transition strain rate from rate independent to dependent yield |

C7 1/MPa | 9.16489 | Kinematic recovery constant |

C9 | 19485.5 MPa | Kinematic anisotropic hardening modulus |

C13 | 282.43 1/(MPa sec) | Isotropic dynamic recovery |

C15 | 109944 MPa | Isotropic hardening modulus |

Cb | 1.49397 | Tension/compression asymmetry constant |

# [edit] References

- ↑
^{1.0}^{1.1}"Magnesium Design", Dow Chemical Co., 1957. As published in*Aerospace Structural Metals Handbook*, vol 3, Code 3603, CINDAS/USAF CRDA Handbooks Operation, Purdue University, 1995, p4